Detailing World  

Go Back   Detailing World > Detailing Products > Polish/Cleaners/Compounds/Glaze
DW Home Forum Home Merchandise Store Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Polish/Cleaners/Compounds/Glaze Discuss Polish/Cleaners/Compounds and Glaze here - Sponsored By g3pro

Reply
 
Thread Tools Display Modes
Old 06-01-2017, 04:12 PM   #1
cleslie
OCD Sufferer (Obsessive Car Detailer)
 
cleslie's Avatar
 
Join Date: Feb 2006
Posts: 1,071
Thanks: 62
Thanked 320 Times in 249 Posts
Garage
Gloss black B pillar tips

When I picked up my pre registered VW CC it had minor swirls all over thanks to numerous dealer washes. I will tackle that in the spring but the gloss black B pillars being softer were worse so I had a go on them this morning. I used a 3M blue finishing spot pad and Megs #205 on a rotary with very light pressure and it made them much better but there is still slight marring. I take it these panels are a high gloss plastic. They must be pretty soft but this combo is the most gentle I have. Any tips? They put these panels on loads of cars these days.
cleslie is offline   Reply With Quote
Old 06-01-2017, 04:15 PM   #2
Frog
Washmitt Meister
 
Join Date: Jun 2013
Posts: 151
Thanks: 71
Thanked 30 Times in 23 Posts
Check out AMMO NYC you tube channel, Larry did one on there recently and then put a clear (bra?) over the top to protect it. It looked quite effective..
Frog is offline   Reply With Quote
Old 06-01-2017, 04:33 PM   #3
cleslie
OCD Sufferer (Obsessive Car Detailer)
 
cleslie's Avatar
 
Join Date: Feb 2006
Posts: 1,071
Thanks: 62
Thanked 320 Times in 249 Posts
Garage
He used #205 too but cleaned the pad off thoroughly after polishing and made a couple of passes again just using the residue in the pad. Will give that a try.
cleslie is offline   Reply With Quote
Old 06-01-2017, 05:25 PM   #4
Alan W
Distinguished Detailer
 
Alan W's Avatar
 
Join Date: May 2006
Location: Southside
Posts: 6,848
Thanks: 1,123
Thanked 2,686 Times in 2,109 Posts
Garage
I don't know what other products you have but an AIO such as AG SRP, AF Tripple or Rejuvenate is less abrasive and could be used with your 3M Blue finishing pad and rotary.

Alan W
Alan W is offline   Reply With Quote
Old 06-01-2017, 06:30 PM   #5
cossiecol
Moderator & Reviewer
 
cossiecol's Avatar
 
Join Date: Jun 2014
Location: Detailing World & Auchterarder
Posts: 4,378
Thanks: 1,338
Thanked 2,497 Times in 1,446 Posts
Garage
Did a wee guide a while ago:

http://www.detailingworld.co.uk/foru...d.php?t=369743
__________________
cossiecol is offline   Reply With Quote
The Following 2 Users Say Thank You to cossiecol For This Useful Post:
Blackwatch (18-01-2017), cleslie (06-01-2017)
Old 06-01-2017, 06:33 PM   #6
cleslie
OCD Sufferer (Obsessive Car Detailer)
 
cleslie's Avatar
 
Join Date: Feb 2006
Posts: 1,071
Thanks: 62
Thanked 320 Times in 249 Posts
Garage
Quote:
Originally Posted by Alan W View Post
I don't know what other products you have but an AIO such as AG SRP, AF Tripple or Rejuvenate is less abrasive and could be used with your 3M Blue finishing pad and rotary.

Alan W
I thought that too. I did give BH Cleanser Polish ago quickly at the end which helped a little but that could be the fillers. It was 4 degrees this morning so not ideal so I'll give it another go as and when it gets warmer. To be honest, the slight marring ex only shows under halogen etc. Under normal conditions it doesn't notice.
cleslie is offline   Reply With Quote
Old 06-01-2017, 06:34 PM   #7
great gonzo
Distinguished Detailer
 
great gonzo's Avatar
 
Join Date: Nov 2010
Location: Reigate Surrey.
Posts: 7,681
Thanks: 2,146
Thanked 2,646 Times in 2,034 Posts
I find you only need a very mild polish, I use dodos micro prime as this breaks down beautifully on soft surfaces.

Before.





After a couple of passes with dodos micro prime on a rotary.






Gonz.
great gonzo is offline   Reply With Quote
The Following 8 Users Say Thank You to great gonzo For This Useful Post:
Blackwatch (18-01-2017), cadmunkey (14-01-2017), camerashy (06-01-2017), cleslie (06-01-2017), Cookies (06-01-2017), Crackers (06-01-2017), Rodriguez (12-01-2017), Welshquattro1 (06-01-2017)
Old 06-01-2017, 07:41 PM   #8
chongo
"Professor"
 
Join Date: Jun 2014
Posts: 5,688
Thanks: 4,386
Thanked 3,375 Times in 1,980 Posts
Garage
Nice finish gonzo
chongo is offline   Reply With Quote
The Following User Says Thank You to chongo For This Useful Post:
great gonzo (07-01-2017)
Old 06-01-2017, 07:44 PM   #9
A&J
OCD Sufferer (Obsessive Car Detailer)
 
A&J's Avatar
 
Join Date: Mar 2015
Location: Location Location
Posts: 1,767
Thanks: 381
Thanked 824 Times in 621 Posts
Yeah I wanted to comment earlier...

Considering how little clear coat there is on B pillars and how soft it is you only need a finishing polish with a soft pad (black for starters, then white if need to) so I agree with Gonz only using DJ Micro prime.

Jon H who used Megs UC...yeah it looks good but he removed way too much clear coat needed. Do that 2-3 times and youll burn through.
A&J is offline   Reply With Quote
The Following 2 Users Say Thank You to A&J For This Useful Post:
chongo (06-01-2017), great gonzo (07-01-2017)
Old 06-01-2017, 07:56 PM   #10
chongo
"Professor"
 
Join Date: Jun 2014
Posts: 5,688
Thanks: 4,386
Thanked 3,375 Times in 1,980 Posts
Garage
Your right A&J, there is no need to use any form of cutting polish at all even on server bi pillars, just a finishing polish is all you need then you can change the pad to gain a bit more cut.
chongo is offline   Reply With Quote
The Following 2 Users Say Thank You to chongo For This Useful Post:
A&J (06-01-2017), great gonzo (07-01-2017)
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 07:47 AM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors
Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors