Detailing World  

Go Back   Detailing World > Gallery > The Showroom > Projects and Restorations
DW Home Forum Home Merchandise Store Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Projects and Restorations Building a car from scratch, restoring your pride and joy, building a track car, or starting a long term project? This is your place to document it.

Reply
 
Thread Tools Display Modes
Old 07-07-2018, 07:08 AM   #141
slim_boy_fat
OCD Sufferer (Obsessive Car Detailer)
 
slim_boy_fat's Avatar
 
Join Date: Jun 2006
Location: Scottish Highlands
Posts: 3,057
Thanks: 2,387
Thanked 1,184 Times in 1,008 Posts
That's a bit odd. My e39 had one and so does the e60. Vents any gasses given off during in-car charging, into the rear o/s wheel arch.

I'm doing a job installing a rear dash cam atm, so will try to grab a clear pic of mine later while I have 'easy' access.

The connection holes on the battery are fitted with a removable plug at wither end, for universal fitting orientation I suppose.
slim_boy_fat is offline   Reply With Quote
Old 07-07-2018, 10:14 AM   #142
Pauly.22
Washmitt Meister
 
Pauly.22's Avatar
 
Join Date: Nov 2009
Location: Birmingham
Posts: 160
Thanks: 74
Thanked 86 Times in 65 Posts
Garage
Quote:
Originally Posted by Starbuck88 View Post

oh wow I've never seen steam coming out the breather before!
https://youtu.be/lJSbqhh17S4

There should defiantly be a breather. Mine had come out from the steam so my boot was quite wet. Could hear the battery boiling on the inside.

Last edited by Pauly.22; 07-07-2018 at 11:24 AM.
Pauly.22 is offline   Reply With Quote
Old 07-07-2018, 10:08 PM   #143
slim_boy_fat
OCD Sufferer (Obsessive Car Detailer)
 
slim_boy_fat's Avatar
 
Join Date: Jun 2006
Location: Scottish Highlands
Posts: 3,057
Thanks: 2,387
Thanked 1,184 Times in 1,008 Posts
Just found out I can't post pic without uploading to a hosting site. I used to use P/Bucket but haven't used an alternative since.

Why can't we upload direct from our PCs, I can on other forums....?
slim_boy_fat is offline   Reply With Quote
Old 08-07-2018, 02:42 PM   #144
Cookies
Distinguished Detailer + Dw Reviewer
 
Cookies's Avatar
 
Join Date: Dec 2008
Location: County Down
Posts: 6,616
Thanks: 10,930
Thanked 4,873 Times in 3,577 Posts
Garage
Quote:
Originally Posted by slim_boy_fat View Post
Just found out I can't post pic without uploading to a hosting site. I used to use P/Bucket but haven't used an alternative since.

Why can't we upload direct from our PCs, I can on other forums....?
You can if thou use tapatalk on your phone or iPad! It'd be great if you could on PC too.

Cooks

Sent from my SM-G950F using Tapatalk
Cookies is offline   Reply With Quote
The Following 2 Users Say Thank You to Cookies For This Useful Post:
SBM (10-07-2018), slim_boy_fat (08-07-2018)
Old 12-07-2018, 06:22 AM   #145
beambeam
Sponge Jockey
 
Join Date: Mar 2007
Location: Scotland
Posts: 89
Thanks: 37
Thanked 44 Times in 28 Posts
Quote:
Originally Posted by Starbuck88 View Post
The battery is secured with a clamp on an extended bar with a 10mm head on the end and a brace that goes across the top.


.
That totally reminds me! I need a replacement bar and clamp and some bolts to fix the clamp in place, been running for ages without!

Nice update, good to see it back on the road!
beambeam is offline   Reply With Quote
Old 13-07-2018, 11:19 AM   #146
wrxmania
OCD Sufferer (Obsessive Car Detailer)
 
wrxmania's Avatar
 
Join Date: Apr 2007
Location: West Lothian, Scotland
Posts: 964
Thanks: 207
Thanked 386 Times in 300 Posts
Garage
Great work so far
wrxmania is offline   Reply With Quote
The Following User Says Thank You to wrxmania For This Useful Post:
Starbuck88 (13-07-2018)
Old 13-07-2018, 02:11 PM   #147
Starbuck88
OCD Sufferer (Obsessive Car Detailer)
 
Starbuck88's Avatar
 
Join Date: Nov 2013
Location: Cornwall
Posts: 2,941
Thanks: 4,636
Thanked 2,252 Times in 1,546 Posts
Garage
The weather was a bit cooler yesterday evening so I thought I'd have a crack at an easy but satisfying job.

The Air Ducts that feed air from the cabin filters into the cabin, where they connect to the bulkhead, the foam has degraded and the previous owner tried to fix it by using black sealant. Didn't do squat and looked a mess.

I bought some closed cell foam tape which I knew would need layering,

As I twisted the passenger side off, I noticed that one of the lugs was broken off, typical on these of people not knowing they twist to get them off. This could actually be the reason engine bay smell is getting in. Anyway, thought I'd do the foam repair and I'll look out for replacements (if used they'll need the foams doing). So I've only done one side.

This is what I pulled off the bulkhead once the duct was removed:



That's tape off the foam, some foam and the messy sealant.

I picked off all soft, squashed, ripped and teared foam off the airduct, I cleaned the old glue off with Chemical Guys Tar and Glue remover and then carefully applied 3 layers of the new closed cell foam.



Voila:



I took the opportunity to clean and Gummi Pflege the rubber sealing ring, should be noted the sealing of the foam to this ring is the inner circumference part of the foam, not the outer.



After:




Final Before:



Finished:



Another thing I noticed, I'm not sure if these are Fibre Reinforced Plastic, when looking inside you can see shiny fibres, I'm concerned the age and heat cycles is causing them to break up and fibres coming off that we're breathing in the cabin.

Video, you can see it sparkling..


I'm going to look out for some replacement ducts and I'm going to get some Bilt Hamber Underbody to coat the inside of them, that way it'll keep them from breaking up.

Looking at the material it says on it that it's PP-MX and PP/EPDM which means it's not actually FRP (I Think) but the shiny little fibres mostly follow the grain so to speak.

Coolant Issue

The car also threw up coolant low warning the other day, funny how the car has now got some peculiar things happened since leaving it sat, I do hope it's nothing more sinister but on inspection the top hose that connects to the thermostat has a crack in the plastic connection.

To the left of the bleed screw on the side of the plastic, you can see pink.



With my inspection camera, you can see a nice crack has developed.



This car is a daily driver, so I have ordered a Genuine BMW Top Hose for £47, it's is easy to change (no need to take off the shroud, viscous fan etc) but I do have all the other hoses, waterpump etc bookmarked to buy, for when I do the proper coolant system refresh. I'll most likely do that when I do the CCV. Also ordered a brass bleed screw as these plastic ones melt.
Starbuck88 is offline   Reply With Quote
The Following 2 Users Say Thank You to Starbuck88 For This Useful Post:
Cookies (13-07-2018), slim_boy_fat (13-07-2018)
Old 13-07-2018, 05:35 PM   #148
Cookies
Distinguished Detailer + Dw Reviewer
 
Cookies's Avatar
 
Join Date: Dec 2008
Location: County Down
Posts: 6,616
Thanks: 10,930
Thanked 4,873 Times in 3,577 Posts
Garage
Great update buddy. Your skills with foam tape are very impressive indeed. That's a very, very tidy job!!!!!

N

Sent from my SM-G950F using Tapatalk
Cookies is offline   Reply With Quote
The Following User Says Thank You to Cookies For This Useful Post:
Starbuck88 (13-07-2018)
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 12:16 AM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors
Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors