Detailing World  

Go Back   Detailing World > Gallery > The Studio
DW Home Forum Home Merchandise Store Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

The Studio The place the Detailing World Supporters display their work for viewing : This is a subscription section you will need to go to your userCP (top left of the page) and select Paid Subscriptions for more information.

Reply
 
Thread Tools Display Modes
Old 13-09-2013, 11:28 AM   #1
*MAGIC*
Distinguished Detailer
 
Join Date: Feb 2007
Location: Detailing studio - Camberley GU15
Posts: 10,251
Thanks: 1,004
Thanked 2,044 Times in 1,013 Posts
Talking Valet Magic Vs Ducati 848 EVO Course SE

Hi Guys


Today saw none other than a good friend King Eric come down to us after his Ducati dealerships had refused point blank to install aftermarket HID kits
stating that they were difficult to install and required minor
modifications of parts to get them to work. Stating that it could be
done over the course of a week as a winter project for him. We have
recently started doing work on motorbikes including details, exhausts
and performance modifications.

On his 848 Evo Corse SE the standard bulbs were not cutting it at all
during night rides in all weathers particularly in wet conditions. As an
all weather rider this started to become an issue so we sourced him an
OEM fit kit from the USA widely used in their market for the Ducati (and
other bike models). The install leaves a clean and factory finish with
the only requirement being a small hole is drilled at the rear plastic
part of the bulb casing to allow the HID wiring loom to run to the relay
and resistor (to prevent flickering-this is a high end kit) and then
down to the battery. Here are some pictures of the process and the
finished articles!!

Fairing removal:-




The high quality HID kit from the USA using 6000k bright white 55w
bulbs. Note the small ballasts making installation into a bike easy and
allows for bespoke fitment.




Bulbs going in to standard holders with absolute 100% fit and seal. Its
rare with aftermarket kits to get such a good OEM fitment at times.




A work in progress shot. Although it appears messy here the wiring
supplied is plentiful to allow installation in almost any suitable
location.




The modified backing plate to the bulb holder to allow the feed for
wiring and the gromett we fit ourselves which along with some sealant
for peace of mind inside provides 100% waterproofing.




The wiring installed




The 848 has an alloy tank so we had to protect it from the tools etc we
were working with. Here you can see the bulb (still in its protective
casing) and the sum total of the wiring required to sit in the existing
housing…once pulled through this allows as much room as the standard
housing provides.




The ballasts are placed on the inside of the fairiings and mounted to
the rear of these inserts to allow free airflow and also a hidden
fitment. Some people have installed ballasts on the top of the lights
next to the actual clocks which in our opinion looks a poor fitment.
With this setup you can also see two simple to remove wiring looms are
popped on and off for future fairing removal.

With the bulbs installed and the fit all complete, the bike was put back
together.

Let there be light. And plenty of it!




All in all an enjoyable job and nice to be around such a stunning bike

The bike is back next week for a protection detail so will post more pics up then

John - Thanks for bringing it to us mate and thanks for making me spit coffee over my workshop floor from the laugh we had

Robbie

Last edited by *MAGIC*; 13-09-2013 at 11:33 AM.
*MAGIC* is offline   Reply With Quote
The Following 2 Users Say Thank You to *MAGIC* For This Useful Post:
neilb62 (13-09-2013), Scottien (13-09-2013)
Old 13-09-2013, 12:03 PM   #2
King Eric
OCD Sufferer (Obsessive Car Detailer)
 
King Eric's Avatar
 
Join Date: Feb 2006
Location: Hampshire
Posts: 3,601
Thanks: 22
Thanked 146 Times in 91 Posts
Thanks mate

The bike needed the lights so badly and glad you could do it! So many people turning it down claiming it was too hard to do. Obviously it's not easy but you guys were great with it. It's the little things a biker looks for when works done...like replacing fairing screws properly. Daft as it sounds some dealers cannot manage it.

I'm yet to see another 848 with Zenons to this day. And now the world can properly see me. Especially when the main is triggered. Fantastic quality of throw too.

Just need the undercarriage lights now for when it's on the back wheel.

Great crack too. Looking forward to working alongside you on the bikes and other stuff in the future
King Eric is offline   Reply With Quote
The Following User Says Thank You to King Eric For This Useful Post:
*MAGIC* (13-09-2013)
Old 13-09-2013, 12:52 PM   #3
GSD
OCD Sufferer (Obsessive Car Detailer)
 
Join Date: Feb 2011
Location: Sheffield.
Posts: 1,076
Thanks: 120
Thanked 445 Times in 353 Posts
What a lovely motorcycle that is,i remember many moons ago with a mate who had a Laverda Jota struggling with Italian electrics then we saw Joe Dolce doing whatsa matter you hey and everything became clear the jota was a brute as i remember it you had to be built like Tyson to pull the clutch in.
GSD is offline   Reply With Quote
Reply

Tags
detailing in surrey, ducati 848 evo, valet magic


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 11:33 PM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors
Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors